Download Download Peplink Pepwave MAX BR1 Pro HW6 Router Firmware 8.1.2 for OS Independent Free

Improvements:

– [5G] Supplement: 5G frequency band and signal information. (For Transit 5G, special firmware will be released after GA to include this function)
– [5G] Cellular “automatic mode” only supports 5G and 4G
Compatible balance: 310 5G
Compatible with X series: EPX, MBX, SDX Pro, SDX, 310X

– [B20X] Added HA support through a valid PrimeCare subscription
Compatible with X series: 20X

– [Cellular] For US mobile SIM cards, the “Data Roaming” option will be enabled by default
Compatible balance: 30 LTE / Pro
Compatible with MAX: BR1/2, HD2/4, Transit
Compatible with UBR: UBR LTE
Compatible with MediaFast: HD2 / HD4
Compatible with X series: all

– [Device API] Added: config.wan.connection has been added: PPPoE_Obj> managementNetwork SIM_Obj> Identity verification status.wan.connection has been added: RAT_Obj
– [System] Added support for service provider configuration through DHCP options
Compatible with all models

– [DHCP WAN] Supplement: Management IP address of DHCP WAN
Compatible with all models (except FusionHub)

– [USB Modem] Update “Modem Support Version” to 1025
Compatible balance: all
Compatible with MAX: BR1 ENT, HD2 / 4 indoor series
Compatible with MediaFast: all
Compatible with X series: all
Compatible with Surf SOHO

solved problem

– [B20X] Fixed memory usage issues that caused system instability
Compatible with X series: 20X

– [B380X / 580X] Fixed an issue that caused the WAN real-time bandwidth on InControl 2 to always display 0 bps
– [B380X / 580X] Fixed an issue that caused the VLAN access port to not work on LAN ports 1-3
Compatible with X series: 380X, 580X

– [B50] Fixed an issue that caused WAN 5 to not operate normally
Compatible balance: 50

– [Captive Portal] Updated the captive portal SSL certificate
– [Cellular | USB] Fixed an issue that could cause high memory usage when not using the phone
– [Outbound Policy] Fixed: Adding a new mandatory outbound policy will not reroute existing sessions
– [SpeedFusion Cloud] Fixed the following issue: If you use “Auto Location”, “Connect Client to Cloud” / “Link Wi-Fi to Cloud” / “Optimize Cloud Application” does not work
Compatible with all models (except FusionHub)

– [Cellular & LTE-US-T / LTE-US-T-M] Fixed: When the network mode is set to automatic, the APN cannot be obtained and the network cannot be switched
Compatible with MAX: BR1 Mini / Mini Core

– [DDNS] Fixed an issue where users could not disable the “Update All Hosts” function when using the “DNS-O-Matic” DDNS service
– [SNMP] Fixed an issue that caused the “SNMP CPU Load” to be inconsistent with the “CPU Load” of the “Web Administrator”
– [System] Now, “Firewall>Allow Access Rules” with “Remote System Log” is sent with severity “Notification” instead of “Alert”
– [System] Fixed an issue that caused function additional keys to not be fully applied to the device
Compatible with all models

– [Flex Module & FlexModule Mini] Fixed an issue that could cause incorrect daily usage reports
Compatible with X series: EPX, SDX Pro, SDX, 580X, 380X, 20X

– [IP Passthrough] Fixed the issue that caused IP pass-through not to work normally after firmware upgrade
Compatible balance: 30 Pro
Compatible with MAX: BR1, Transit
Compatible with UBR: UBR LTE
Compatible with Surf SOHO: SOHO HW2 / MK3
Compatible with X series: 20X

– [KVM] Fixed the issue of disabling the creation of virtual machines over the network
Compatible with MediaFast: 500, 750
Compatible with X series: SDX Pro

– [LDAP] Fixed an issue where remote user access with LDAP authentication was not applicable to Windows Server
– [LDAP] Fixed LDAP authentication issue when using DUO MFA
Compatible balance: 210 or above
Compatible with MAX: 700, HD2 / 4
Compatible with MediaFast: all
Compatible with X series: all
Compatible with FusionHub

– [MBX] Fixed: The old MBX hardware revision does not support the new MBX expansion module
Compatible with X series: MBX

– [Remote User Access & FusionHub] Fixed an issue where authentication using Active Directory would fail if the server name could not be resolved
Compatible with FusionHub

– [SpeedFusion] Added the option to ignore the DF bit of the packet
– [SpeedFusion] Fixed potential memory issues caused by devices with a large number of SpeedFusion profiles
– [SpeedFusion] Remove duplicate SpeedFusion event log entries
Compatible balance: B210 or above
Compatible with MAX: 700, HD2 / 4, Transit
Compatible with UBR: UBR LTE
Compatible with MediaFast: all
Compatible with SFE
Compatible with X series: EPX, SDX Pro, SDX, PDX, MBX, 310X
Compatible with FusionHub

About switch firmware:

Given that there are many models and different ways to upgrade the switch, if you want to apply this software package, even if you are an advanced user, we recommend that you read and understand the installation steps before installing the new firmware.

Generally, the update process is not troublesome, because manufacturers try to make it as simple as possible. However, some situations are exceptions to this rule. First, please go to the system information page of the switch to check that the currently installed version is not a newer version or matches the release version.

The application of new firmware can reduce security vulnerabilities, enhance overall performance and compatibility, improve various power management functions, resolve different errors, and increase support for newly developed technologies and protocols.

It is recommended that you perform this step in a stable power environment, such as the power environment ensured by the UPS device, and do not interrupt the upgrade in any way, as this may cause the switch to malfunction.

Having said that, please click the download button to get and apply the new version, and then keep visiting our website to keep up with the latest version.