Download Download MikroTik RouterOS X86 Firmware 7.8 Beta 3 for OS Independent Free

Important tip! ! !

– This version is not recommended for use on CRS3xx devices.

Changes in this release:

– Storage – Added new “rose-storage” package to support extended disk management and monitoring capabilities (ARM, ARM64, Tile and x86) (CLI only);
– Bridging – fixed adding disabled MSTI;
– Bridge – Improved hardware offload logic;
– certificates – fixed PBES2 certificate import;
– Certificates – improved multi-certificate import process;
– Console – Improved “:execute” command to output a string when no file is specified;
– dhcpv4-client – when used, sends DHCPv4 unicast requests to a DHCPv4 relay instead of a server;
– dns – fixed reading CNAME from cache;
– dns – respond to DNS requests for static domain names with “NOERROR” when no record of the appropriate type is configured or found on the upstream server;
– Health – Fixed “Temperature” and “Power Consumption” readouts for RB1100AHx4;
– ike2 – fixed active SA refresh for responders after failed peer connection attempts;
– ipsec – fixed peer matcher for incoming connections to unresolved DNS;
– ipv6 – improved handling of state changes for “advertised” IPv6 addresses;
– led – fixed signal readout for KNOT devices;
– lte – LtAP improved modem detection in lower mini-PCIe slot (requires “/system router board upgrade”);
– pimsm – improve system stability;
– poe – Added LLDP power management support for 802.3at PSE;
– pppoe – fixed PPPoE client scan showing only one server;
– Routing – added hop limit and metric parameters for SLAAC routing;
– routerboot – fixed format storage for RBM33G devices (requires “/system routerboard upgrade”);
– routerboot – fixed routerboot protected for RBM33G devices (requires “/system routerboard upgrade”);
– sfp – Improved optical module SFP compatibility on CCR2004-16G-2S+, CCR2004-1G-12S+2XS, CCR2116-12G-4S+ devices;
– switch – fixed “switch-cpu” counter (introduced in 7.8beta2);
– USB – Changed USB auto-detection behavior to default to external USB when internal USB device is not detected
– vxlan – Added FastPath support;
– webfig – improved terminal handling;
– wifiwave2 – Adjust monitoring of site interfaces to report when the interface is authorized, not just connected;
– wifiwave2 – fixed 802.11r fast transition when using wpa3-psk authentication (introduced in 7.8beta2);
– winbox – Added “Connect” button under “WifiWave2/Scan” menu;
– winbox – Added “Disable/Enable” button under “WifiWave2” menu;
– winbox – Added “Provision” button under “WifiWave2” menu;
– winbox – Added “Start at boot” checkbox under Containers menu;
– winbox – Added “Tx Rate” and “Rx Rate” columns under “WifiWave2/Registration” menu;
– winbox – added missing password property for OVPN server and client;
– winbox – added missing filter property under Tools/Packet Sniffer menu;
– winbox – added missing property when setting “Use DoH server”;
– winbox – added support for manual RAM filesystem (TMPFS) creation under the System/Disks menu;
– winbox – add type “https-get” parameter under “Tools/Netwatch” menu;
– winbox – Allow bridge selection for static entries under Bridge/MDB menu;
– winbox – hide “TTL” value for static DNS entries of type FWD;
– winbox – hide unnecessary properties of virtual interface under “WifiWave2” menu;
– winbox – Rename “Multicast Router” monitoring property to “Is Multicast Router” under “Bridge” menu;
– zeroter – Fixed routing after VRF changes;

Other changes since v7.7:

– bgp – fixed setting of “default-prepend” parameter;
– Bridge – fixed PVID warning typo;
– Certificates – improved certificate management, signing and storage procedures;
– conntrack – Improved system stability when changing connection tracking state;
– Containers – Added authentication option to registry (CLI only);
– container – fixed “.type” file ownership;
– Containers – fixed file ownership for containers running on internal disk after system upgrade;
– Containers – Fixed several containers starting automatically on boot;
– disk – limit maximum TMPFS size;
– dns – Added configurable DoH concurrent query limit parameter (CLI only);
– dns – do not cache the results of the “:resolve” command from a specific server;
– dns – limit “DoH max concurrent queries reached” log message to once per minute;
– Firewall – fixed bridge priority target;
– Firewall – fixed DSCP priority target for IPv6 Mangle;
– Firewall – Fixed IPv6 NAT’s network mapping range maximum address calculation;
– Drawing – Fixed hiding target queue when “Allow Target” is disabled;
– Drawings – fixed ordering of interface and queue diagrams;
– Drawings – properly handle disabled and statically bound interface diagrams;
– Drawing – Removed “Move” command for drawing rules;
– Hotspot – fixed setting of the “Address” parameter for IP bindings;
– hotspot – resume cookie timeout on reboot;
– ike2 – Added support for ‘address’, ‘keyid’ and ‘dn’ for remote ID matching (CLI only);
– ipsec – added support for “Framed-Route” RADIUS attribute support;
– ipsec – does not match incoming IKE requests from peers with unresolved DNS names;
– ipv6 – added “pref64” option configuration for RA;
– ipv6 – limit the “hop-limit” parameter value range to 255;
– ipv6 – make the distributed DNS life cycle conform to RFC8106 standard;
– l3hw – Add destination MAC address check for offloaded FastTrack connections;
– lte – Added AT support for Telit LE910C4 in MBIM mode;
– lte – Fixed APN setting usage on initial connection attempts for AT-based Quectel and Neoway modems;
– LTE – Fixed automatic antenna selection on Chateau LTE12/LTE18;
– lte – Fibocom L850-GL module fixed dial;
– lte – fixed display “subscriber number”;
– lte – improved AT port matching for SIMCom, Huawei, WeLink, Cinterion, BandLuxe and Sierra modems;
– lte – improved modem detection speed in lower mini-PCIe slot on LtAP;
– lte – parse USSD even if the encoding is not supported;
– mpls – Fixed handling of more than 9 VRFs;
– mpls – fixed LDP listen socket creation before IPv6 address is ready for use;
– mpls – improved stability on neighbor router reboots;
– ospf – fixed “ospf-type” parameter for OSPFv3 routing;
– ospf – fixed simple authentication for OSPFv3;
– ovpn – Added AES-GCM and multicore encryption support (CLI only);
– poe – Proper power off on hAP ax2 and hAP ax3 when no link detected;
– Port – fixed modem channel number on KNOT;
– Resources – displays file system related statistics on CCR2004;
– Routing – fixed IPv6 default route received from RA exists;
– Routing – fixed printing of “count only” parameter of routing table;
– sfp – fixed false link detection for S+RJ10 on RB5009;
– sfp – fixed reading of SFP EEPROM on single SFP port devices;
– SMS – improved reporting of SMS sending errors;
– SMS – record USSD response when sending USSD via MBIM;
– Sniffer – Added additional filtering parameters (CLI only);
– snmp – do not reveal identity in LLDP when branding is used with hidden SNMP data;
– snmp – fixed handling of disabled routes;
– snmp – fixed reporting of total route counters;
– ssh – hardcoded “localhost” address for forwarding requests;
– sstp – fixed TLS session establishment when “connect-to” is a DNS name;
– Switch – fixed SFP rate selection for CRS354 devices;
– Switches – Improved system stability for 98DXxxxx switch chips;
– torch – allow Torch’s “no pagination” parameter;
– Traffic Generator – increased maximum allowed flow count;
– Upgrade – display error message when license prohibits upgrade;
– vxlan – added “dont-fragment” setting that allows managing fragments;
– webfig – allow to set value in time interval field;
– webfig – Fixed access to WebFig when the “Interface” menu is disabled by skins;
– webfig – fixed multi-field parameter editing with “no” checkbox;
– webfig – fixed handling of empty skin files;
– webfig – improved navigation responsiveness;
– webfig – improved skin file parsing;
– webfig – properly escape all reserved URI characters;
– webfig – updated WebFig and figure web pages to HTML5;
– wifiwave2 – Added wifi sniffer tool to capture wireless transmissions (CLI only);
– wifiwave2 – Enables additional channels in the UNII-3 and UNII-4 bands for Europe and the US on hAP ax^2, hAP ​​ax^3 and Chateau ax;
– wifiwave2 – implements 802.11w management protection SA query procedure;
– wifiwave2 – improved protection against WPA3 denial of service attacks;
– winbox – Added “Match subdomain” parameter under “IP/DNS/Static” menu;
– winbox – added missing WifiWave2 related parameters under “WifiWave2” menu;
– winbox – Fixed display of “Default Prefix” value under “Route/BGP/Session” menu;
– winbox – Fixed display of “Tx/Rx CCQ” value under “Wireless/Registration” menu;
– winbox – fixed the display of the logo under the “System/Console” menu;
– winbox – fixed display of multi-character flags;
– winbox – fixed use of IPv6 family addresses under “IP/Web Proxy/Access” menu;
– winbox – Improved mouseover hints for “Local” policies under the “System/Users/Groups” menu;
– winbox – Show “Gateway” column by default under “IPv6/Routing” menu;
– x86 – Added support for TP-Link TG-3468;
– x86 – fixed SR-IOV support for Intel X710 series NICs;
– x86 – Improved support for Intel 500 series 10G SFP modules;
– x86 – improved stability for Intel X550 series NICs with SR-IOV;

About router firmware:

Before considering downloading this firmware, go to your router’s system information page and make sure that the currently installed version is neither newer nor matches this version.

Due to the variety of router models and device upgrade methods, it is strongly recommended that you read and most importantly understand the installation steps before applying new firmware, even if you are an advanced user.

In theory, these steps shouldn’t be too much of a hassle for anyone, as manufacturers try to make them easy, even if they don’t always succeed. Basically, you have to upload new firmware to the router and allow it to upgrade via its admin page.