Download Download Peplink MediaFast MFA 200 HW1 Router Firmware 8.2.1 for OS Independent Free

Known issues:

– [FlexModule Plus Ethernet Module] PoE LED will remain “off” after reboot
– [FlexModule Plus 3x SFP+ Module and HA] If FlexModule Plus SFP+ is configured as LAN and HA with “Resume Master Role Upon Recovery” is enabled, Slave unit cannot change back to Slave role after Master unit is recovered
Affected X-Series: EPX, SDX Pro SDX

Improve:

– [Cellular | Cat-20] Added carrier selection option
– [Cellular | Cat-20] Supplement: RAT connection method and frequency band selection
Compatible with devices with 4G Cat-20 cellular WAN

– [Remote User Access] Added: Remote User Access now supports VLAN interfaces in plug-in mode
Compatible with all models

– [SpeedFusion Connect] Added option to disable Peplink relay delay checking
– [SpeedFusion Connect] Renamed SpeedFusion Cloud Home to SpeedFusion Cloud Relay
Compatible with all models (except FusionHub)

Issues resolved:

– [B20X] Fix: Device configuration may revert to factory default after firmware upgrade
– [B20X] Fixed WINS server not working
Compatible with X-Series: 20X

– [System] Fix: SIP RTP traffic is dropped if RTP port number is lower than 1024
– [CLI] Fixed: “get wan” command displayed incorrect DNS information
– [DHCP] Fixed: DHCP Offer packets are incorrectly broadcast instead of unicast to client DHCP requests
– [DHCP] Fixed: DHCP max lease count could be wrong if DHCP reservations were defined. The DHCP client may not be able to obtain an IP address.
– [InControl] Fixed: WAN Quality report on InControl could incorrectly show 2400ms cellular WAN latency
– [System] Fixed packets being incorrectly routed to the Hot Standby WAN when Low Data Mode is enabled
– [System] Fixed: CVE-2022-0778
– [System] Fix: DHCP server does not reply to unicast DHCP update packets
– [System] Fixed: Scheduled restart does not work if InControl Management is disabled
– [System] Fix: WAN status shows ISP’s DNS if “Obtain DNS server address automatically” is disabled
Compatible with all models

– [Wi-Fi WAN] Fixed: Wi-Fi AP may stop working if Wi-Fi WAN is enabled on the same radio
– [Wi-Fi WAN] Fixed: Wi-Fi WAN upstream could sometimes be limited to 20Mbps
Compatible with MAX: 700, BR1/2, HD2/4, Transit (Excludes: BR1 ENT, HD2 Mini, HD1/2 Dome)
Compatible with UBR: UBR LTE
Compatible with MediaFast: HD2/4
Compatible with X series: PDX, MBX
Compatible with Surf SOHO

– [5G] Fixed best network discovery bug shown on 5G cellular WAN.
Compatible Balance: 310 5G/Fiber 5G
Compatible with X-Series: EPX, MBX, SDX Pro, SDX, 310X

– [BR1 5G Pro] Fixed: PepVPN performance was unexpectedly low
– [Wi-Fi AP | Wi-Fi 6] Fixed: Wi-Fi client fails to connect if client signal strength threshold is defined
Compatible with MAX: BR1 5G Pro

– [EPX] Fixed: Some options in Cellular WAN are missing after device boot
Compatible with X-Series: EPX

– [HD4] Fix: Wi-Fi LED always off if Wi-Fi interface is in WAN mode
Compatible with MAX: HD4

– [MAX Transit] Fix: System may become unstable when Wi-Fi interface is turned on
Compatible with MAX: Transit

– [MBX Mini] Fix: MAC address conflict on internal interface
Compatible with X-Series: MBX Mini

– [Surf SOHO MK3] Fixed: Incorrect WAN latency detected
Compatible with Surf SOHO: SOHO MK3

– [USB Ethernet] Fixed: Anker USB Ethernet Adapter (AK-A7610011) not working
Compatible Balances: All
Compatible with MAX: BR1 ENT, HD2/4 indoor series
Compatible with MediaFast: All
Compatible with X-Series: All
Compatible with Surf SOHO

– [Wi-Fi AP] Fix: Wi-Fi APs with WPA2 Enterprise SSID may not work after upgrading from 8.1.3 or below to 8.2.0
Compatible Balance: 30 Pro, one
Compatible with MAX: All (Excludes: BR1 ENT, HD2 Mini, HD1/2 Dome)
Compatible with MediaFast: HD2/4
Compatible with X-Series: PDX, MBX, 20X
Compatible with UBR: UBR LTE
Compatible with Surf SOHO

important Notice:

– InControl must be enabled on PrimeCare devices to update software features such as SpeedFusion (bonding, WAN smoothing, hot failover).
– Further major firmware updates will not support Balance 20 hardware revisions 1-6. They will receive firmware 8.1.x maintenance releases as needed.
– PepVPN backward compatibility option is no longer available. By deprecating older firmware versions, we now have a more secure handshake channel as the default, accepting only TLS 1.2 and no longer accepting TLS 1.0 and 1.1 for older devices. Therefore, if you are using devices running firmware 6.1 or earlier, you will no longer be able to form PepVPN tunnels with these devices unless the firmware is updated.

About router firmware:

Before considering downloading this firmware, go to your router’s system information page and make sure that the currently installed version is not a newer version or matches this version.

Due to the wide variety of router models and different methods of device upgrades, it is highly recommended that you read and most importantly understand the installation steps before applying new firmware, even if you are an advanced user.

In theory, these steps shouldn’t be a hassle for anyone, as manufacturers try to make them as simple as possible, even if they don’t always work out. Basically, you have to upload the new firmware to the router via its management page and allow it to upgrade.

If you install the new version, you can expect a higher level of security, different bug fixes, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, and several other changes.

If you’re looking for some safety precautions, keep in mind that it’s best to use an ethernet cable rather than a wireless connection to perform the upload, as wireless connections can easily be interrupted. Also, if you want to avoid any glitches, make sure you don’t turn off the router or use its buttons during installation.

If this firmware meets your current needs, get the version you want and apply it to your router unit; if not, visit our website as often as possible to avoid missing updates that improve your device.