Download Download MikroTik RouterOS MMIPS Firmware 7.3 Beta 40 for OS Independent Free

New in 7.3beta40:

– queues – CAKE types are not allowed in simple and tree setups (configured queues will be disabled);
– bgp – added “name” parameter for connection;
– bgp – fix “keepalive-timeout” value when upgrading from RouterOS v6;
– bgp – fixed “l2vpn” distribution;
– Bridge – added more details on loop detection warnings;
– Bridges – do not use the “set” command to set VLANs on inactive ports;
– Bridge – Ignore VLAN tagged BPDUs;
– capsman – Improved traffic handling on CAP communication tunnels:
– chr – fix Cloud DDNS update after license renewal;
– dot1x – fix RADIUS state attribute when client re-authenticates;
– dot1x – fixed port-based VLAN ID assignment on devices without switch chips;
– dot1x – improved server system stability during authentication;
– ipsec – fixed printing of active peer statistics;
– l3hw – improved unloading in case of hardware table overflow for CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
– l3hw – optimize offload when dealing with a large number of directly connected hosts;
– lte – Added SMS sending support for MBIM protocol;
– lte – only MCC/NMC format is allowed in the “operator” parameter;
– lte – clear SIM value when modem is in “stop” state;
– mpls – improved LDP AF selection process and behavior;
– ntp – disallow setting the port number in the “server” parameter;
– ovpn – Adjusted SHA2 authentication algorithm naming to allow legacy OpenVPN connections;
– ovpn – improved server stability under continuous overload;
– ovpn – reply with the same IP address from which the connection was established;
– ppp – added support for VRF;
– romon – Fixed VLAN tagged packet handling;
– Routing – Fixed IPv6 /127 routing next hop resolution;
– routerboot – prevent “protected-routerboot” from being enabled on unsupported factory firmware versions;
– sfp – fixed link baffles for QSFP+ and QSFP28 ports in case the base interface changes “operational” state (introduced in v7.3beta33);
– sfp – hide empty monitor values ​​in console;
– snmp – VRF support added (CLI only);
– snmp – fixed disk size reported when connecting multiple external disks;
– snmp – report “ifSpeed” as 0 if value is out of range (use “ifHighSpeed” instead for high-speed interfaces);
– ssh – added AES-GCM cipher support;
– ssh – removed DSA public key authentication support;
– supout – added simplified IPv4 and IPv6 routing table printing;
– switch – fixed “switch-cpu” port stats for 98DXxxxx and 98PX1012 switches (introduced in v7.3beta37);
– Switches – Fixed missing stats in traffic monitor for 98DXxxxx and 98PX1012 switches;
– System – Fixed kernel timer consistency;
– Tunneling – improved packet handling on EoIP, IPIP and GRE tunnels;
– vpls – fixed TE transmission path usage after startup;
– vrrp – fixed bridge-local MAC address learning;
– winbox – added missing “IBGP”, “EBGP”, “limit exceeded” and “stopped” parameters under “Routes/BGP/Sessions” menu;
– winbox – Added missing “Preserve Send Properties” parameter under “Route/BGP/Connection” menu;
– winbox – added missing “scan list” parameter for W60G interface;
– winbox – added missing BGP session commands;
– winbox – added support for 2.5Gbps and 100Gbps ethernet speed options;
– winbox – don’t show “Session Uptime” parameter under “LTE” menu if modem doesn’t support it;
– winbox – fixed “Disconnect Timeout” parameter type under “CAPsMAN” menu;
– winbox – fixed refresh of “IP/Cloud” window after detected changes;
– winbox – correctly load band values ​​under “LTE” menu;
– winbox – removed obsolete “routing table” parameter under “IP/Firewall” menu;

About router firmware:

Before considering downloading this firmware, go to your router’s system information page and make sure that the currently installed version is not a newer version or matches this version.

Due to the wide variety of router models and different methods of device upgrades, it is highly recommended that you read and most importantly understand the installation steps before applying new firmware, even if you are an advanced user.

In theory, these steps shouldn’t be a hassle for anyone, as manufacturers try to make them as simple as possible, even if they don’t always work out. Basically, you have to upload the new firmware to the router via its management page and allow it to upgrade.

If you install the new version, you can expect a higher level of security, different bug fixes, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, and several other changes.

If you’re looking for some safety precautions, keep in mind that it’s best to use an ethernet cable rather than a wireless connection to perform the upload, as wireless connections can easily be interrupted. Also, if you want to avoid any glitches, make sure you don’t turn off the router or use its buttons during installation.

If this firmware meets your current needs, get the version you want and apply it to your router unit; if not, visit our website as often as possible to avoid missing updates that improve your device.